Beiträge von xlarge

@ thgoebel

Hallo,

Fantastic, but as eiche said, to expensive (Pro unit and electrician) for this simple connection.

But, very much thanks to you for full introduction to Shelly Pro AP setup. I may need this later.

Just now many have told me to try another (not Shelly) cheap AP unit. Several say that this will work as good as a Shelly Pro AP, but I am a little unsure if shelly cloud (via Wan) can find the Shelly 1PM.

(I have several Shelly Pro units there, but they are only in use in the summer and the Shelly 1PM with temp. must also work the rest of the year.)

Zitat von eiche

May I write in german?

If you need the measurements on the fly, you may use the internal Access Point of a Shelly 1 PM generation 2+.

But if you want to store the measurents values, I may have a solution for you, based on a script. This script stores many values into its non volatile storage and you may take it to your home for reading this values. Alternatively you may use a MQTT transfer over your smartphones hotspot without replacing the Shelly, if you use a MQTT subscriber at home.

Btw, my solution via script may be used with a smartphone directly reading the stored values. I've created this script for using MQTT, but it may be used without MQTT.

If you are interested in my solution: https://iotig.eichelsdoerfer.net/index.php/loes…r-shelly-script

Thank you. You mention Shelly 1PM gen 2+. Has this unit connecton to ethernet? And I am not looking for an AP in the Shelly 1PM but how to give the unit wifi connection. History values is the question,. but thanks, now I know it's possible.

Zitat von tvbshelly

Only the PRO series Shellys have a LAN connection.

By the way: The Pro 1PM is not like a fuse, but a relay. Or do you mean the shape of the housing?

Thanks, but sorry it is to bad that there is no such solution. Something for Shelly in the future?

I need the local Wifi to connect to a Shelly 1PM with temperature monitoring in an area I can't reach with wifi. (In a swimming pool pump house where I measure the temperature of the water before and after the heat pump as well as in the air.)

I have ethernet there, but the Shelly 1PM needs Wifi. Therefore, the need is either something similar to the Shelly 1PM with temperature measurement for ethernet or another ethernet Shelly unit that can give me local wifi.

I am aware that the Shelly Pro 1PM and similar can do this, but it will be quite expensive with electricians etc.

thgoebel. Ignore my last question. Of course, the Shelly Plug S in off cannot be overloaded.

Zitat von thgoebel

A cut-off due to exceeding the power limit should not shut down the Shelly totally. The device should be operating but with open contact.

Last question; Will "operating with open contact" be status also when I via shelly cloud has clicked off or it is in off state due to schedule? Thank you for perfect help so far.

Thanks, I think that is the case. It seems that I still have power to the heaters. But as you told me earlier there is no way to refresh / restart them when i not am on place.

Danke sehr!

As Shelly Plug S should work even one phase suddenly is down giving about 140v I begin thinking of my setting for max w. I don't remember exactly, but I normally set max power 200w higher than the oven / heaters max consum. This because I years ago discovered that one heater used more than it should. Happily Shelly reported this and saved me for possible overload and fire.

If the case is that the Shelly Plug S har cut off because the power max load has been set to low (when suddenly power cut off), is it possible to restart them without being on place?

Thanks for answer.

I have of course tried to reach the Plug S through my online connection. And the mentioned ealier failure killed the Shelly Plug S totally. There was no way to get them alive again, even I tried everything onplace. I think it is the same now, but can't check it out now.

I hope it is possible to trust Shelly units, but if I need to fix things on place I must search for alternatives. Sorry to say, I have 20-30 Shelly units.

1. I need to hear from Shelly (or forum) if my problem is a common one.

2. Has Shelly Plug S been tested when one phase on 3 phase power 230v drops out, meaning should the plug tolerate 2/3 of 230v?

3. Further on pkt. 2, should I install an contactor rele in the fuse-box before everything?

I have a smart home with Shelly Plug S in front of all the heaters, but my 2 Shelly Plug S died at the same time at 00:15 26.1.24 at the same time as the power went out according to notification from my alarm company Verisure (which gives immediate notification).

I have lost several other Shelly Plug S in recent years without finding a cause, but now I am 100% sure that the power outage has something to do with it. The power came back 5 hours later and everything else works - also some other Shelly Plug S. All my Shelly Plug S are used in front of ovens with 1000-2000w on 230w. Another unit, Shelly Pro 1 PM tells me that voltage is 238,9v.

I have been in contact with an electrician who is wondering if the power plant has had a phase failure (I have 3-phase with 230v), but I find it strange that it can kill the plugs. They recommend installing a relay and contactor. The fuse box and fuses are brand new.

There has been no thunderstorm, but a lot of wind and the power outage probably has something to do with it.

Can't Shelly Plug S handle lower voltage than 230v +/- 10%? Are they dead then, or can they be restarted? Can I restart them via OpenVPN-connection (as I am situated 300 km away)?

After hours with several tries, I need help.

Starting with reset to fabric setup, next using ipad with the new cloud app (and with wifi to my nearest router) I add the new unit.

Everything went smooth incl. new name, picture and room. No failure, but next window in the app is the unit with pending connection - with only 5 choices avaliable (Temperatur - no data, Activity log - no data, Applications settings - nothing, Share - nothing and Device information - Device id (OK), Decimal id (OK), Device IP - cound not load data, Device Type - Shelly H&T, Device Network - Couldnt load data, Device signal - Disconnected.

I have tried to activate the unit (blinking slowly) with no result.

I have checked my wifi - same as before.

The only thing I can point at is that the picture of the shelly H&T is white, but my unit is black. No black found.

Please help me.

I updated several Shelly Plug S last evening - and everything went OK, but today several of them began "Safety" cut off. At least two of them connected to ovens with 800w and 1000w suddenly displayed real time 900-950w and 1250-1330w. Pic from the 1000w oven.

I checked further with a Tibber Pulse which show power consume in the fusebox and there the consume was as earlier 780-790w resp. 970-990w.

Something happen with the Shelly Plug S after the update.

Is it possible to revert to older update - or can the last update be fixed very soon as this disturb everything in my smart houses?

Thank you very much, thgoebel.

We 'll try the single phase scheme.

Hi again,

May be How to connect to a 3 phase network without neutral #20 is what I should use?

Phase 1 to terminal VA, current clamp A

Phase 2 to terminal VB, current clamp B

Phase 3 to terminal N

Terminal VC open, current clamp C empty.

Supply voltage is 230V AC between two phases.

Thanks thgoebel - in this rainy afternoon.

I live in Norway and we have not "N", but use two phases to get 230 volt. I found a connection diagram with 2 phases, but as I think my electrician to have connected all 3 phases in the main switch - each to random one phase fuses, I suppose we should connect the 3EM to exact the same phases (fuses).

My question was also if I must buy 3 phase fuses. But possibly NO as you didn't reply to that.

Can Shelly 3EM be used in my setting: Main switch/fuse is 3phase, but all other fuses are one phase where the goal is total consumption measurement?

Do I have to buy and replace 3 of my one phase fuses with 3phase fuses to have 3EM to give me total consumtion?

I have tried to read everything about this matter, but can't find simular case.

I have questioned in the English Shelly forum, but it seems to be a failure from Shelly. https://www.facebook.com/groups/ShellyI…07386982693955/

The case is very important for us who pay electricity per hour. Therefore I use schedule to switch on / off ovens when the hourly price makes it desirable. But I discover in the cloud app (and when downloading) that I do not get the same hourly measurement as I pay for. Example: Schedule start 06:00 or 06:30 (and stop 07:00) appears in the cloud app as start 05:30. If I download, I get time 06:00, 07:00 etc., but don't know if 06:00 gives me consumption for 05:30-06:30 or 06:00-07:00. Data for 05:30-06:30 is useless for me and all others who want to save electricity and money when we pay for 06:00-07:00.

But is the case that the measurement is correct and Shelly Cloud shows errors, I would like to know.

Thank you very much, MIHO.

Can anybody help me? I want to switch a Shelly Pro 1PM on/off when the temperature is below 28 or above 31 C in a Shelly 1PM temp.addon. (If it not already is on respectively off).

If it is possible via http, what is the syntax and preferably the entire command string?

My case is AP on a Shelly Pro 1 used by a Shelly 1PM with temp.add. The ordinary wifi from my router to my pool's service room is too weak and I have therefore set up the Shelly 1PM with the ordinary wifi on Wifi 1 and Wifi 2 with wifi from the AP.

But, I get offline in Shelly Cloud APP when Wifi 1 is too bad. How to connect when wifi 2 (the access point's wifi) is used?

It is fine to configure the plug as AP, but I am not sure if I will then lose the usual use - power management.

I can get in touch with 192.168.33.1 in my browser, but how do I get it in the app? (in the same room)

In the english forum they say:

The original line of devices don't function simultaneously as client & AP.

Is that the fact - and the plug can't be both AP and handle power measurment?