Beiträge von Eric3412

Hi,

The pin is only managed in the app.

- To set the pin code : go to settings->user settings->lock pin

-To enable on the device : go to applications setting->pin lock on the device page on the app

For login and password :

- In the app :

- Or in the device web ui :

Hi,

I think it's impossible, but I can't say for sure. Never found any official info about that.

Here another person who tried without success.

cannot save report url

Seems only status work with direct cloud url.

"https://shelly-21-eu.shelly.cloud/device/status?id=XXXXXXXX&auth_key=ZZZZZZZZZ"

Zitat von michelds

ok,

Instead of the inter ip address (192.168...) the external internet ip address.

For my cameras I use port forwarding, but for Shelly I see no possibility to open a port.

Shelly just use port 80. You can use port forwarding by redirecting any port to port 80.

For example, I redirect 8019 to 80

So, for local IP :

http://192.168.1.19/light/0?turn=on&brightness=100

I use external IP :

http://my_internet_ip:8019/light/0?turn=on&brightness=100

I don't keep redirect enable, so I don't use authentication, but it is preferable if the redirection remains active.

http://login:pass@my_internet_ip:8019/light/0?turn=on&brightness=100

Hi,

What do you mean by "external" url ?

If you control your device with a local PC as you say in the second post, you just need to use the device url, for example :

http://192.168.1.10/light/0?turn=on&brightness=100

Corrected in 5.2.14, even if the widget doesn't seem as responsive as before.

Hi,

With the new version released today on play store (5.2.13/bb66088) widget doesn't work any more (at least for HT sensor) ans make the app crash.

Mark as resolved

I "resolve" the problem by removing the HT sensor from the app and adding again. Hoping it doesn't happen again.

Hi,

Perhaps try to update with an intermediate version between 1.10.4 and 1.11.8

https://shelly-forum.com/index.php?shelly-firmware-archive/

Hi,

Since this morning, without any change, the "setting pending" message appears on the HT page.

I try to restart/reset the device, I reset the app cache and data, but nothings helps, the message is still here.

Is there a way to throw it away ?

Not a big issue, but it takes space for nothing and it's annoying.

Zitat von andybev

BUT......as a result of nothing being connected to to the O terminal of the Shelly 1L, would the Shelly 1L actually work, with just a permanent Live input?

Hi,

No, it can't work.

Without neutral, the Shelly sink a small amount of current through the load to power itself. Without neutral and without load, it has no way to get power, so it can't work.

Zitat von iangbarton

I try to set my Latitude and Longitude manually but it doesn't allow me to edit the values.

Hi,

Just uncheck "automatically detect time-zone and Geo-Location" and you will be able to set Latitude and Longitude manually.

Zitat von dcleal

Hi,

but HTTPS action URLs don't work.

Hi,

Are you sure it should work ?

I never read that Shelly support HTTPS for IO actions URL. All documentation and examples I see are with HTTP.

I use a Shelly 1L (firmware 1.11.8) to send commands to a Shelly Dimmer2 and a Shelly plus 1, and it works fine.

I use IO actions on :

Button 1 Long push

Button 2 Long Push

Button 2 Short Push

All works fine. My "Button type 1" is configured as "momentary on release" and "Button type 2" detached.

Hi,

No, sleep_mode.period is not a configurable parameter, it's fixed depending on external_power setting.

Hi,

Not possible to use Shelly directly connected to this kind of system, with is not a simple motor but a complete system. Shelly outputs (O1 et O2) is Line, and here you need a "Com." to drive up and down.

The manual clearly indicates : Cables 1, 2, 3 of the bus lines MUST NOT be connected to be electrical mains.

I don't know how you have connected your motor, but if you have connected as standard motor like below, it's possible you have destroy your system.

Zitat von biomass

PS: check Account Management: Settings - Notifications

I think is the answer for that :

Zitat von BobSwede

Question about this forum:

How do I get email alert if/when someone replies to this thread?

See if they are connected to the router, and try to connect to their ip before attempting the electrical restart.

It should be possible with I/O URL if actions for button was available.

Unfortunately with shelly 2.5 in roller shutter mode, even if button are in detached mode, actions are only available for roller open/close/stop, not for button.

I think an important thing to check to try to understand the origin of the problem is the one described here :

Dimmer 2 turn on led

Unfortunately no one seems to be watching the source in the status.