It is possible to set the dimming and brightening effect directly in the shelly application.
When I set the effect in Google Assistant, the dimming works well, but the daylighting is done in such a way that the light is fully lit first and then the brightness decreases. Does the type of calibration or the button play a role?
I don't use the back physical button.
All mains powered devices work great in home assistant. But not battery-powered, concrete shelly motion 1 and 2. Entities (motion, temperature and battery status) say they are not available. I have the settings correctly according to the instructions, I use coiot. I'm using the official integration from Shelly. This problem exists for many people and I have not found a satisfactory solution or at least an explanation of why it is so. You can see the data in the shelly application, so why not in the home assistant?
Hat down, you're a genius:). That's exactly how you drew it. It never occurred to me that I could send a phase from one box to another. For some reason, the electrician didn't connect it. I am your debtor, if you need to consult something in IT I will be happy to help you.
I'm sorry, I was busy here, so I couldn't react. I'm sending a photo of box X. Today I tried to reconnect in box A and failed again. In my opinion, the problem is with the wire connecting to terminal O. This wire is terminated in the box and is energized according to the condition of the switches, but not permanently. The pernament phase that is connected to the input of switch is only in box A, not in box X. Unfortunately, I can't even turn on the light shelly with the application. The state is that the light switch turns on / off (they flicker in one of the four states) and the application only turns on the shelly, not the lights.
The setting is original. In my weekly schedule, I was set to turn off at midnight and turn on at 6 in the morning. The wifi turns off at midnight and also turns on at 6 in the morning, so it is possible that before the wifi turned on, it did not have time to turn on the sensor and later this setting is no longer applied. Possible?
Any suggestion?
Shelly motion sometimes stops working. When motion is detected, it flashes green, but the light (through the action) does not start, nothing is logged. In the application, the sensor reports as "Non active".
What is causing this and how to deal with it?
Unfortunately, this does not solve the situation. It's just a toilet for information. The light turns off after a minute, but the sensor does not turn it on again when it is in the motion detected state. During this time, the blind time is still activated.
I do not understand now. Where should I apply the delay? The switch physically turns off the light, but the sensor runs a blind time during which the sensor does not respond. Blind time cannot be turned off.
Does it work for you with the toggle type? The sensor switches off the light. It does not work when switched off with the switch during blind time (minimum 1 minute).
Shelly1:
It does not work with the toggle type, the switch does not know what the status is, so it must be pressed empty. With the edge type, it works the same as in the case of scenes. So when the light turns on the sensor and I turn it off with the switch, the sensor doesn't work for another minute. Is there a way to solve this?
Ah, it can be stored there, but the light does not come on. Are you sure there should be /relay//0?turn=on, not just /relay/0?turn=on or /light/0?turn=on? Btw, what does 0 mean for relay? Doesn't there have another number?
But I manage scene from my wwla and cloud is allowed.
When i change motion detected action. In place where I wrote URL is just [object].
What I am doing wrong?
I think, you can try in this way:
- delete the scenes
- Action in Motion with DDD to the Shelly1 to switch light on when motion is detected
- Action in Motion with DDD to the Shelly1 to witch light off when no motion detected
- Switch at Shelly1 in mode "toggle"
Oh, I haven't tried this option yet. Unfortunately, I can't find in the documentation how to set it up. if I set the action for motion detected in shelly motion http://shelly1_ip/light/0?turn=on and save it, then it is in the appropriate field [object]. Could you describe to me how to do it? BTW shouldn't the scenes do the same?
You can choose edge mode to trigger the Shelly to turn its output on and use a delayed off function of 20 seconds for example, to turn it off.
The thing is that the motion sensor will not be ready, to detect a next motion, before the 60 seconds have elapsed.
Therefore it's always wise to select a sensor with a short blind time.
Oh sorry, I didn' see, that you are writing of the Shelly motion sensor, so there is not much choice.
So shelly motion cannot be use with manual switch?
Turn off the shelly1 with 60 seconds delay.
I have it set up through the scene. When the sensor detects movement, I turn on the relay. In the second scene, the opposite. How do I turn off shelly 1 for 1 minute? Doesn't the light go out immediately or will it go off with the switch?
Hi,
I have classic switch with shelly 1 and shelly motion. I can switch on / off light with switch and sensor. When i come into the room the sensor lights up. When I leave and turn off the light switch, the sensor does not work for 1 minute. This is the smallest blind time value that can be set. Is there a way to make sure that the sensor and switch work and remember the latest state? Something like an edge mode for turning on and off through an application.
But just when switch one is turn on. I need to switches work in the same way as without shelly.
Sorry I was out couple of days. In second switch is not permanent phase. I mean, place for shelly is correct.
