Beiträge von mikec

I got a second Shelly 1 in today and I can confirm that this setup works as intended now. Thank you SebMai for your excellent support!

Zitat von SebMai

Right, it is unused afterwards. The Shelly on the second switch only sends an http command to the first. And the first one takes over the switching.

Got it, I will order up a second Shelly 1 and give this a try. Thank you for the help!

Zitat von SebMai

Sorry it isn't the best, but hope you understand it.

( Grey = removed/ changed)

Der Inhalt kann nicht angezeigt werden, da Sie keine Berechtigung haben, diesen Inhalt zu sehen.

Ok, so the red wire from the second switch is not going to the lamp at all, is that right?

A couple things to try, In the Shelly app, go to the Timer and make sure you have an Auto Off set for 1 second. This may be why you have to press the button twice on your Kelly garage door module. Also go into Settings->Button Type and make sure both are set as a Detached Switch. It almost sounds like you didn't do this for your Ken module and the reed switch is acting as an actual on/off switch instead of a state sensor. As far as your non-functional wall switch, it sounds like you may have disconnected one of the leads when you were attaching the Shelly, so trace back the cables from the wall switch and ensure they are still firmly attached to the garage door opener. Finally go into Application Settings->Input State and check the button for Add input identifier so you can see the status of your reed switches in the App.

Zitat von SebMai

Wiring need to be changed.

I explain it with the same colors.

First switch.

Black from com to Black at L

Red disconnect from switch

Shelly N at white

Shelly L/I at black

Shelly SW at switch com (old red or black place)

O at red.

Ceiling

Black from Lamp at black coming from switch

White to white at the lamp

Red coming from first switch at the lamp (where black was before)

Second switch

Red disconnect from switch

Black at live

White disconnect from switch

Shelly N = white

Shelly L = black

Shelly SW where red or white was.

Shelly I/O empty

Later I will explain how to setup that they work together, I'm at work

Edit: Explain working

First switch Shelly button type edge

Second switch Shelly button type detached (should work with this actions, if not than button type toggle)

Actions Switch on/off (both)

Code

http://ipFirstShelly/relay/0?turn=toggle

Alles anzeigen

Sorry, I'm having some trouble understanding. Would it possible for you to make a sketch? When I try to follow along with your instructions I come up with this diagram and I don't understand how the second switch is connected to anything at all

Zitat von SebMai

I'll think about it a little more, but at the moment I've only found the option to use 2 Shelly1. I haven't come up with a way with just one

If you were to use two separate shellys how would you wire them in for the above listed diagram?

I've reattached the diagram

Hello all,

I would like to install a Shelly 1 in my house where I have a three-way light setup in my basement. The wiring for this particular light has the power from the mains going to the first three-way switch, from there it goes to the light and then to the second three-way switch (see diagram)

. Can anyone advise if a Shelly will work in this configuration? I've run out of ideas and can't think of where I can install a Shelly1 into this setup while maintaining the functionality of both switches.

This issue was resolved for me with the last firmware update that got pushed out 12/28/2020. Prior to that I was using a Home Assistant automation as a work around to trigger the dimmer on when it received power.

Zitat von SebMai

You haven't say what you have set into "Power on default mode" but it have to be "on".

Eventually have you "Restore last mode"

I’ve tried all three options, On, Off and Restore Last mode. Off is the only one that works as intended. When I use On or Restore Last the lights come on momentarily then shut off.

Hello all,

I have a Shelly 2 dimmer that is working great with a pair of lamps. I currently have the Shelly 2 wired inline on an extension cord which feeds to a pair of nearby lamps. The issues I am experiencing is that the outlet that the Shelly 2 is connected to is a smart outlet that turns on and off on a programmed schedule. Whenever the outlet is turned off, all power to the Shelly is cut off and when the outlet is turned back on the Shelly has power again. The problem is that when the power is restored to the Shelly, my lamps momentarily turn on and then turn off again. I am forced to go into the app and manually toggle the lamps back on. I want the Shelly and my lamps to come on and stay on as soon as the Shelly gets power, I thought this is what the "Power On Default Mode" setting was for but it doesn't seem to be working. Any suggestions how to fix this issue?

FYI - I have other devices on this outlet that I don't want dimmed, however I want them all on/off at the same time which is why I'm using the smart outlet