Beiträge von Corvl

Hello again ,

I have ordered some new Unis, waiting for delivery.

In the meantime I also received word from support how to connect , and it is completely the opposite.

In this thread it is said:

-connect pin 7 or 8 to one pin of the switch , the other side of the switch to the + of the 12V DC which also powers the UNI, in that case I would have a status change when I press the button.

Support is saying:

Zitat

My question last week :

On the picture of the manuel it says , connect wire 7 or 8 to the switch.

It is unclear where to connect the other side of the switch. I would assume GND , but before I do so , I would like to confirm. I have wired the UNI to a 12V DC power source.

Answer I received just now from support:

Yes, you are correct.
Also the reed switch should work on both ways (1 and 2 )

-That is the complete opposite: Connect pin 7 or 8 to one side of the switch and the other side of the switch to the - of the 12V DC power supply.

Now I don't know what to do.

Do you also have access to the ticket system? this is the ticket number: #T-20043426

Thanks,

Cor

Ticket has been opened.

In the meanwhile I will order some new ones.

To be sure with the next one(s) I receive; according the picture from post #7 it is connected correctly?

How it is set up now , I should have on channel 1 this blue vertical line (contact closed)?

Many thanks for your assistance.

Cor

Got a bigger issue now. I am unable to contact the UNI. I am trying to reset the device (pressing the reset button and than apply the power), but nothing , the led light stays on.

I also noticed the chip below the led is getting extremely hot.

Is this device toast, or can I do something else.?

Thanks,

Cor

Same as you described.

Cor

Hello,

Ah, I see , inputs and outputs are coupled. Good to know ( maybe that can be written in the manual with a next update).

But unfortunately no luck here, I can toggle the outputs channel 1 and 2 via the GUI in a webbrowser. But I can not toggle channel 1 /2 via the inputs.

Attached a photo. The switch/button I removed for the moment for testing purposes. Pin 7 (light brown) is directly connected to the + from the 12V DC.

I also tried with Pin 8 ( brown) , directly connected to the + from 12V DC.

There is no change in the state of the channel 1 or channel 2.

Thanks,

Cor

Dear Olsche,

I do have Channels 1 & 2 , but those are the outputs , they are working fine. I am talking about the inputs.

I connected a small led to output/relay 1 and when I press the button on then GUI in the webbrowser the light goes on, that part is working fine.

The question is for the input. I expect , that when I press the switch/button (Pin 7 is than connected to the + of the 12VDC ) something happens on the GUI.

Or are you saying the input (pin7) is internally wired to the output relay 1 ?

Thanks,

Cor

@Olsche , Thank you for taking the time.

-I have now connected pin 7 to one side of the switch.

-the other side of the switch is connected to the + of the power supply which also powers the UNI (12V DC).

When I press the button , nothing happends. Sould I see a change in the GUI somewhere? where ?

Thanks,
Cor

Dear all ,

I have bought some Shelly devices and installing as we speak the UNI. I would like to use a switch to controll something in Homeseer.

Let's say a simple doorbell, a push button. How do I connect it, I would say:

-connected to 12 V DC

-on pin 7 or 8 one side of the switch

-on the other side ground.

If this is correct , how do I see the change in the GUI, for example the webbrowser. I only have 2 relays and the ADC voltage. no other inputs.

Anyone can help?

Thanks,

Cor