Beiträge von Corvl

Maxxl . I think, PR -thingy as well.

I have now 1 Pro 3EM , working just fine , next week the solar panels will be installed. Just wondering If I buy a second Pro3EM , and put them on the 3 phases of the solarpanels , so I know what is coming in and what is used . Or doesn't it work like that??

I will get an app where I can monitor the PV -stuff , but I would like to have it in my home automation as well..

Thanks,

Cornelis

Danoo , "unidentified" is bad wording indeed ....... my bad english.

Thanks for the tip.

I have just looked again , and this is the count now:

The other screenshot was taken about 1 weeks ago , so it accumulates from when the device was first powered up I think.

It is now 153130Wh = 153Kwh in one week , that would make sense that number , when I see the energy bill over 12 months.

I just deleted all saved data , and it looks like it is all I needed

*edit*

Thanks for the link

https://shelly-api-docs.shelly.cloud/gen2/ComponentsAndServices/EMData

Many thanks for your help,

Cornelis

Hello ,

I have installed a Shelly pro 3EM. In the near future I will be getting photovoltaic panels on my house (10KWp , 3 phase) .

The manual of the Shelly pro3EM says it is "ready" for photovoltaic.

What can I do with this? , measure how much energy is brought in by the photovoltaic panels on each phase , just like now how much energy is used by all electronics? .

I guess I have to buy a separate one for the photovoltaic system?

Does it need to be connected to the other one for example , or are there special settings?

Thanks,

Cornelis

Hello,

I have installed a Shelly pro 3EM and it is working fine, On the Shelly APP I see a lot of data and I would like to have this data also in my homeseer (HS4) system. I am usiing MQTT to get all he data from Shelly.

Can someone help me understanding which topics/data is what?

Especially I am looking for KWh (totall for the 3 phases) and to know how to interpret this data , is it reset everyday at 00:00 for example?

Here are all the topics broadcasted which are "unidentified":

Many thanks,

Cornelis

OK thank you .

Just want to make sure , no smoke will get out .

Thanks,

Cor

Hello again ,

I have ordered some new Unis, waiting for delivery.

In the meantime I also received word from support how to connect , and it is completely the opposite.

In this thread it is said:

-connect pin 7 or 8 to one pin of the switch , the other side of the switch to the + of the 12V DC which also powers the UNI, in that case I would have a status change when I press the button.

Support is saying:

Zitat

My question last week :

On the picture of the manuel it says , connect wire 7 or 8 to the switch.

It is unclear where to connect the other side of the switch. I would assume GND , but before I do so , I would like to confirm. I have wired the UNI to a 12V DC power source.

Answer I received just now from support:

Yes, you are correct.
Also the reed switch should work on both ways (1 and 2 )

-That is the complete opposite: Connect pin 7 or 8 to one side of the switch and the other side of the switch to the - of the 12V DC power supply.

Now I don't know what to do.

Do you also have access to the ticket system? this is the ticket number: #T-20043426

Thanks,

Cor

Ticket has been opened.

In the meanwhile I will order some new ones.

To be sure with the next one(s) I receive; according the picture from post #7 it is connected correctly?

How it is set up now , I should have on channel 1 this blue vertical line (contact closed)?

Many thanks for your assistance.

Cor

Got a bigger issue now. I am unable to contact the UNI. I am trying to reset the device (pressing the reset button and than apply the power), but nothing , the led light stays on.

I also noticed the chip below the led is getting extremely hot.

Is this device toast, or can I do something else.?

Thanks,

Cor

Same as you described.

Cor

Hello,

Ah, I see , inputs and outputs are coupled. Good to know ( maybe that can be written in the manual with a next update).

But unfortunately no luck here, I can toggle the outputs channel 1 and 2 via the GUI in a webbrowser. But I can not toggle channel 1 /2 via the inputs.

Attached a photo. The switch/button I removed for the moment for testing purposes. Pin 7 (light brown) is directly connected to the + from the 12V DC.

I also tried with Pin 8 ( brown) , directly connected to the + from 12V DC.

There is no change in the state of the channel 1 or channel 2.

Thanks,

Cor

Dear Olsche,

I do have Channels 1 & 2 , but those are the outputs , they are working fine. I am talking about the inputs.

I connected a small led to output/relay 1 and when I press the button on then GUI in the webbrowser the light goes on, that part is working fine.

The question is for the input. I expect , that when I press the switch/button (Pin 7 is than connected to the + of the 12VDC ) something happens on the GUI.

Or are you saying the input (pin7) is internally wired to the output relay 1 ?

Thanks,

Cor

@Olsche , Thank you for taking the time.

-I have now connected pin 7 to one side of the switch.

-the other side of the switch is connected to the + of the power supply which also powers the UNI (12V DC).

When I press the button , nothing happends. Sould I see a change in the GUI somewhere? where ?

Thanks,
Cor

Dear all ,

I have bought some Shelly devices and installing as we speak the UNI. I would like to use a switch to controll something in Homeseer.

Let's say a simple doorbell, a push button. How do I connect it, I would say:

-connected to 12 V DC

-on pin 7 or 8 one side of the switch

-on the other side ground.

If this is correct , how do I see the change in the GUI, for example the webbrowser. I only have 2 relays and the ADC voltage. no other inputs.

Anyone can help?

Thanks,

Cor