Beiträge von Johnny

    Can I use 50A clamps for measurements (with redoing the connector)

    Actually good question…. Can we not just cut the cable and reconnect (soldering) the cables of a 50A clamp to it?

    I know we need that special plug to insert it to the 3EM.

    Has anyone already done this and is it working?

    J

    quelle? - die leute welche dass melden sowie mich..... seit letzte woche habe ich problemen mit den App und nicht nur auf IOS aber auch auf web zugang or Android. Dass ist deutlich ein Server problem

    Der Inhalt kann nicht angezeigt werden, da Sie keine Berechtigung haben, diesen Inhalt zu sehen.
    Hi,

    Wenn I look at your picture above, I don’t see the option of “Calibrate with bypass”?

    and when calibration is completed you should see “delete calibration” as it will be stored. So start calibration should be replaced with delete when successful calibration.

    I would try to reset your dimmer 2 to factory settings and do again from start.

    Johnny

    Hi,

    I had same issue when I tried via the app, I made a stand alone system... meaning via power socket connected - with a switch - and outlet of Shelly to the lamp what I was planning to dim.

    Connected via http address - upgraded FW to BETA - changed to trailing edge.

    Then I powered off the system and repowered.... checked again all system settings if still ok like trailing edge.

    Then I did the calibration, it started in my case at 50 after ca 10 seconds waiting and it took ca 1 minute to complete calibration to 100%.

    When completed all was working fine, I installed permanent in the wall.

    So... try via http to calibrate your system, maybe it helps.

    Good luck,

    Johnny

    Hallochen,

    Ich muss mich ein neue Router anschaffen und habe die Asus RT-AX88U im auge zu kaufen laut Seine gutte leistung dass ich gelesen habe.

    Aber, in nicht kompatibel router liste ist einen router angegeben, Asus AC-RT88U und ich hoffe dass es hier nicht um dass RT-AX88U geht.

    Ist der jemanden welche die Asus RT-AX88U in betrieb hat zuhause ohne problemen mit die Shelly’s?

    Muchte gerne kein 280 Euro ausgeben an ein router wenn es nicht funktioniert.

    Danke, Johnny

    PS: Mein Deutch ist nicht perfekt und der sind sicher schreibfehler drinnen.... ( bin von Belgien) :)

    Hi, I had 2 Eltako dimmers in my livingroom, these where working ok but I wanted to expand my wireless so I purchased 2 pieces Shelly Dimmer 2. I just want to share how I did it.... I have currently no issues.

    My first trial to set it up failed - dimmer got overheated, a lot of blinking, interference with other led lamps who also started to blink and so on.

    So, I decided to restart and this time everything works flawless. So, in short - what did I do:

    1) connected Shelly Dimmer 2 stand alone on power

    2) changed IP to static ( outside DHCP)

    3) after connecting to my home network, update firmware to the BETA version.

    4) made a temporary setup with the Shelly dimmer 2 + impuls switch + connected outlet of dimmer to my living room lamp (orginal feed kabel disconnected). In this way I had a stand alone system.

    5) power on on system - via web interface (not the app) connected to dimmer to change settings.

    6) changed to trailing + did calibration via web interface.

    7) when calibration was completed, powered of the system and powered on again.

    8. still via web interface checked the system, all was working flawless - no blinking - no sound and I could use the full range of dimming.

    9) tested now via the app and also here no issue.

    10) installed all in the wall and powered on the system - all ok.

    11) did the same for second dimmer and as expected all ok.

    I must say, I always configure and test my Shelly devices via web interface as it seems functioning better for setting up your device then via app ( in my case)

    Just wanted to share my findings as I see that many have issue with blinking and sound.

    PS: my lamps are from WOFI: https://www.wofi.de/innenleuchten/…e-hampton-12flg

    PS2: when I installed my Eltako some years ago, I had also issues with blinking.... I found out that in my switchboard the fase was switched with the zero, so I asssumed I was dimming on the fase :) After is switched the cables in the switchboard all blinking was gone.

    Great board here... tomorrow my other stuff to be installed, Shelly EM, Shelly 1PM and more.

    Greetings, J.

    I noticed that username is case sensitive, maybe that could be the issue as in my case the first letter was not capital but when I typed it , it was set as capital due to auto correction.

    After I typed my username again correctly, without capital and it was ok.

    GL,

    Johnny